uart驅動，linux設備模型之tty驅動架構分析,linux設備模型之uart驅動架構分析

五： uart_add_one_port()操作本文引用地址：http://www.eepw.com.cn/article/201610/305916.htm

在前面提到。在對uart設備文件過程中。會將操作轉換到對應的port上，這個port跟uart_driver是怎么關聯起來的呢?這就是uart_add_ont_port()的主要工作了。

顧名思義，這個函數是在uart_driver增加一個port.代碼如下：

int uart_add_one_port(struct uart_driver *drv, struct uart_port *port)

{

struct uart_state *state;

int ret = 0;

struct device *tty_dev;

BUG_ON(in_interrupt());

if (port->line >= drv->nr)

return -EINVAL;

state = drv->state + port->line;

mutex_lock(port_mutex);

mutex_lock(state->mutex);

if (state->port) {

ret = -EINVAL;

goto out;

}

state->port = port;

state->pm_state = -1;

port->cons = drv->cons;

port->info = state->info;

/*

* If this port is a console, then the spinlock is already

* initialised.

*/

if (!(uart_console(port) (port->cons->flags CON_ENABLED))) {

spin_lock_init(port->lock);

lockdep_set_class(port->lock, port_lock_key);

}

uart_configure_port(drv, state, port);

/*

* Register the port whether it's detected or not. This allows

* setserial to be used to alter this ports parameters.

*/

tty_dev = tty_register_device(drv->tty_driver, port->line, port->dev);

if (likely(!IS_ERR(tty_dev))) {

device_can_wakeup(tty_dev) = 1;

device_set_wakeup_enable(tty_dev, 0);

} else

printk(KERN_ERR Cannot register tty device on line %d\n,

port->line);

/*

* Ensure UPF_DEAD is not set.

*/

port->flags = ~UPF_DEAD;

out:

mutex_unlock(state->mutex);

mutex_unlock(port_mutex);

return ret;

}

首先這個函數不能在中斷環境中使用。 Uart_port->line就是對uart設備文件序號。它對應的也就是uart_driver->state數組中的uart_port->line項。

它主要初始化對應uart_driver->state項。接著調用uart_configure_port()進行port的自動配置。然后注冊tty_device.如果用戶空間運行了udev或者已經配置好了hotplug.就會在/dev下自動生成設備文件了。

操作流程圖如下所示：

六：設備節點的open操作

在用戶空間執行open操作的時候，就會執行uart_ops->open. Uart_ops的定義如下：

static const struct tty_operations uart_ops = {

.open = uart_open,

.close = uart_close,

.write = uart_write,

.put_char = uart_put_char,

.flush_chars = uart_flush_chars,

.write_room = uart_write_room,

.chars_in_buffer= uart_chars_in_buffer,

.flush_buffer = uart_flush_buffer,

.ioctl = uart_ioctl,

.throttle = uart_throttle,

.unthrottle = uart_unthrottle,

.send_xchar = uart_send_xchar,

.set_termios = uart_set_termios,

.stop = uart_stop,

.start = uart_start,

.hangup = uart_hangup,

.break_ctl = uart_break_ctl,

.wait_until_sent= uart_wait_until_sent,

#ifdef CONFIG_PROC_FS

.read_proc = uart_read_proc,

#endif

.tiocmget = uart_tiocmget,

.tiocmset = uart_tiocmset,

};

對應open的操作接口為uart_open.代碼如下：

static int uart_open(struct tty_struct *tty, struct file *filp)

{

struct uart_driver *drv = (struct uart_driver *)tty->driver->driver_state;

struct uart_state *state;

int retval, line = tty->index;

BUG_ON(!kernel_locked());

pr_debug(uart_open(%d) called\n, line);

/*

* tty->driver->num won't change, so we won't fail here with

* tty->driver_data set to something non-NULL (and therefore

* we won't get caught by uart_close())。

*/

retval = -ENODEV;

if (line >= tty->driver->num)

goto fail;

/*

* We take the semaphore inside uart_get to guarantee that we won't

* be re-entered while allocating the info structure, or while we

* request any IRQs that the driver may need. This also has the nice

* side-effect that it delays the action of uart_hangup, so we can

* guarantee that info->tty will always contain something reasonable.

*/

state = uart_get(drv, line);

if (IS_ERR(state)) {

retval = PTR_ERR(state);

goto fail;

}

/*

* Once we set tty->driver_data here, we are guaranteed that

* uart_close() will decrement the driver module use count.

* Any failures from here onwards should not touch the count.

*/

tty->driver_data = state;

tty->low_latency = (state->port->flags UPF_LOW_LATENCY) ? 1 : 0;